Husqvarna TC 50 2023 страница 65 Скачать руководство пользователя

Страница: 65 / 196

SERVICE WORK ON THE CHASSIS 11

K00654-11

–

Close quick release

11.30

Removing the air filter

Note

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

–

Only operate the vehicle if it is equipped with an air filter.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Preparatory work

–

Remove the seat. (

p. 62)

K00671-10

Main work

–

Press rear holding lug

together slightly and swing the air

filter box cover upward.

–

Pull out the front holding lug and take off the air filter box

cover.

–

Take off the air filter.

11.31

Installing the air filter

K00672-10

Main work

–

Position the clean air filter.

–

Position the rear holding lug. Lower the air filter box cover
and allow the front holding lug

to snap in.

Info

If the air filter is not mounted correctly, dust and dirt

may enter the engine and result in damage.

Finishing work

–

Mount the seat. (

p. 62)

Содержание TC 50 2023





































































































































































































Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды

Husqvarna TC 50 2023, Руководство пользователя

Результаты поиска

Содержание TC 50 2023

Отзывы:

Похожие инструкции для TC 50 2023

Бренды по названию

Популярные бренды