background image

1. Antenna
2. Indicator for remote control connection
3. Indicator for radio communication (RX)
4. Connection for power cord
5. CAN
6. Connection for remote control cable
7. Button for pairing operation

Product description

The product is a reversible plate compactor for

compaction of granular soils in moderately thick layers

to layers of larger depth. The product has a combustion

engine.
The model LH 700 is pedestrian-controlled.
The model LH 804 is operated by a remote control at a

maximum distance of 20 m from the operator.

Intended use

The product is for professional operation only. Use the

product for compaction of different types of fill material,

from sand to rocks. Do not use the product for other

tasks.

Symbols on the product

WARNING: This product can be dangerous

and cause serious injury or death to the

operator or others. Be careful and use the

product correctly.

Read the manual carefully and make sure

that you understand the instructions before

you use the product.

Read the manual carefully and make sure

that you understand the instructions before

you use the product.

Use hearing protection.

Ultra-low-sulfur diesel fuel only.

Hydraulic oil level.

Bio-Hydr.

Biological hydraulic oil.

Lifting point on the safety frame.

Noise emission to the environment as

referred to in the EC directive. The emission

of the product is specified in 

Technical data

on page 26

 and on the label.

This product is in compliance with applicable

EC directives.

XXXXXXXXXX

LH 700: Keep your hands away from this

area.

LH 700: Risk of crush injuries.

LH 700: Risk of injuries. The engine has

moving parts.

LH 700: Risk of injury if the handle falls on

you. Lock the handle in the lifted position.

LH 804: Hydraulic oil pressure.

LH 804: Main switch. Battery ON/OFF.

Do not clean the engine

with a high-pressure

washer.

Note: Other symbols/decals on the product refer to

special certification requirements for some markets.

4

1177 - 001 - 02.04.2020

Содержание LH 700





































Отзывы: