Husqvarna HS 139A Скачать руководство пользователя страница 41

Страница: 41 / 48

8 Technical data

8.1 Technical data

HS 139A

HS 166A

Brand

Husqvarna

Engine type

Single cylinder, 4-Stroke,

Forced Air Cooling, OHV

Single cylinder, 4-Stroke,

Forced Air Cooling, OHV

Displacement, cm

139

166

Idle speed, rpm

1800±150

Max. engine speed, rpm

2900±100

Max. power, kW/3600 rpm

2.4

2.9

Max. torque, Nm/2500 rpm

7.5

9.5

Cylinder pressure

, kg/cm

4.0-6.0

Bore × stroke, mm

65×42

65×50

Compression ratio

8.3 :1

8.5 :1

Rotation

Counterclockwise (from P.T.O.

side)

Counterclockwise (from P.T.O.

side)

Engine lubrication type

Splash

Nominal engine output, kW

2.2

2.75

Ignition system
Start

Recoil start

Ignition

Transistorized magneto Ignition Transistorized magneto Ignition

Spark plug

Husqvarna HQT-7

Electrode gap, mm

0.7-0.8

Valve clearance
Inlet valve, mm

0.10~0.15

Exhaust valve, mm

0.10~0.20

0.10~0.15

Fuel and lubrication system
Fuel tank capacity, litre

0.9

1.0

Fuel consumption, g/kW·h

≤395

Oil tank capacity, litre

0.5

Engine oil

SAE 10W-30

Weight
With empty tanks, kg

8.9

9.5

Dimension
Without P.T.O., L×W×H, mm

369 × 345 × 261

391 × 340 × 278

Measured at no load

Measured at 600 rpm.

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production en-

gine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from

this value. Actual power output for the engine installed on the final product will depend on the operating speed,

environmental conditions and other values.

1425 - 001 - 03.06.2020

Technical data- 41

Содержание HS 139A

















































Результаты поиска

Содержание HS 139A

Отзывы:

Похожие инструкции для HS 139A

Бренды по названию

Популярные бренды

Husqvarna HS 139A, Руководство по ремонту

Результаты поиска

Содержание HS 139A

Отзывы:

Похожие инструкции для HS 139A

Бренды по названию

Популярные бренды