Husqvarna FE 450 Скачать руководство пользователя страница 98

Страница: 98 / 128

16 COOLING SYSTEM

F00451-10

–

Position the motorcycle upright.

–

Place a suitable container under the water pump cover.

–

Remove screw



. Take off radiator cap



–

Completely drain the coolant.

–

Mount and tighten screw



with a new seal ring.

Guideline

Screw, water pump cover

10 Nm (7.4 lbf ft)

16.5

Refilling coolant

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

F00452-10

Main work

–

Make sure that the screw



is tightened.

–

Stand the vehicle upright.

–

Pour coolant in up to measurement



above the radiator fins.

Guideline

10 mm (0.39 in)

Coolant

1.2 l (1.3 qt.)

Coolant (

p. 117)

–

Refit the radiator cap.

Finishing work

–

Take a short test ride.

–

Check the coolant level. (

p. 95)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды