manualshive.com logo in svg

Husqvarna FE 450, Руководство пользователя

Поделиться
Скачать
Husqvarna FE 450 Скачать руководство пользователя страница 71

12 SERVICE WORK ON THE CHASSIS

69

12.44

Changing the hydraulic clutch fluid

Warning

Skin irritation

 

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not designed for DOT 5

brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

F00311-10

–

Move the clutch fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws

.

–

Remove cover

with membrane

.

F00454-10

–

Fill bleeding syringe

with the appropriate hydraulic fluid.

Bleed syringe (50329050000)
Brake fluid DOT 4 (

p. 117)

–

On the clutch slave cylinder, remove bleeder screw

and mount bleeding

syringe

.

F00324-10

–

Now inject the fluid into the system until it emerges from drill hole

of the mas-

ter cylinder without bubbles.

–

Now and then, extract fluid from the master cylinder reservoir to prevent overflow.

–

Remove the bleeding syringe. Mount and tighten screws bleeder screw.

–

Correct the fluid level of the hydraulic clutch.
Guideline

Fluid level below container rim

4 mm (0.16 in)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

Содержание FE 450

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды