Husqvarna FE 450 Скачать руководство пользователя страница 70

Страница: 70 / 128

12 SERVICE WORK ON THE CHASSIS

F00323-10

–

Check that screw



is firmly seated.

Guideline

Screw, fixed grip

5 Nm

(3.7 lbf ft)

Loctite

243™

Diamond



must be located at the top.

12.42

Adjusting the basic position of the clutch lever

F00310-10

–

Adjust the basic setting of the clutch lever to your hand size by turning adjusting
screw



Info

Turn the adjusting screw clockwise to increase the distance between the

clutch lever and the handlebar.
Turn the adjusting screw counterclockwise to decrease the distance

between the clutch lever and the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not apply any force.
Do not make any adjustments while riding!

12.43

Checking/correcting the fluid level of the hydraulic clutch

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.

F00311-10

–

Move the clutch fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws



–

Remove cover



with membrane



–

Check the fluid level.

Fluid level below container rim

4 mm (0.16 in)

» If the level of the fluid does not meet specifications:

–

Correct the fluid level of the hydraulic clutch.

Brake fluid DOT 4 (

p. 117)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Бренды по названию

Популярные бренды