Husqvarna FE 450 Скачать руководство пользователя страница 68

Страница: 68 / 128

12 SERVICE WORK ON THE CHASSIS

F00469-10

–

Check the chain sliding piece for wear.
» If the lower edge of the chain pins is in line with or below the chain sliding

piece:

–

Change the chain sliding piece.

–

Check that the chain sliding piece is firmly seated.
» If the chain sliding piece is loose:

–

Tighten the screw of the chain sliding piece.
Guideline

Screw, chain sliding piece

15 Nm

(11.1 lbf ft)

400985-01

–

Check the chain guide for wear.

Info

Wear can be seen on the front of the chain guide.

» If the light part of the chain guide is worn:

–

Change the chain guide.

F00322-01

–

Check that the chain guide is firmly seated.
» If the chain guide is loose:

–

Tighten the fitting on the chain guide.
Guideline

Remaining screws, chassis

10 Nm

(7.4 lbf ft)

Remaining nuts, chassis

10 Nm

(7.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 45)

12.38

Checking the frame

F00255-01

–

Check the frame for cracks and deformation.
» If the frame exhibits cracks or deformation due to a mechanical impact:

–

Change the frame.

Info

Always replace a frame that has been damaged due to a mechan-

ical impact. Repair of the frame is not authorized by Husqvarna

Motorcycles.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды