Husqvarna FE 450 Скачать руководство пользователя страница 67

Страница: 67 / 128

12 SERVICE WORK ON THE CHASSIS

12.37

Checking the chain, rear sprocket, engine sprocket, and chain guide

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 45)

400227-01

Main work

–

Shift the transmission to idle.

–

Check the rear sprocket and engine sprocket for wear.
» If the rear sprocket and engine sprocket are worn:

–

Change the drivetrain kit.

Info

The engine sprocket, rear sprocket, and chain should always be

replaced together.

400987-10

–

Pull at the top part of the chain with the specified weight



Guideline

Weight of chain wear measurement

10… 15 kg (22… 33 lb.)

–

Measure distance



of 18 chain rollers in the lower chain section.

Info

Chain wear is not always even, so you should repeat this measurement at

different chain positions.

Maximum distance



at the longest

chain section

272 mm (10.71 in)

» If distance



is greater than the specified measurement:

–

Change the drivetrain kit.

Info

When the chain is replaced, the rear sprocket and engine sprocket

should also be changed.
New chains wear out faster on old, worn sprockets.

F00470-10

–

Check the chain sliding guard for wear.
» If the lower edge of the chain pins is in line with or below the chain sliding

guard:

–

Change the chain sliding guard.

–

Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:

–

Tighten the screws on the chain sliding guard.
Guideline

Screw, chain sliding

guard

6 Nm

(4.4 lbf ft)

Loctite

243™

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды