Husqvarna FE 450 Скачать руководство пользователя страница 64

Страница: 64 / 128

12 SERVICE WORK ON THE CHASSIS

Main work

–

Check throttle cable routing. (

p. 67)

F00309-11

–

Position the fuel tank and fit the two spoilers to the sides in front of the radiator

bracket.

–

Make sure that no cables or throttle cables are trapped or damaged.

F00308-11

–

Attach the fuel tank breather hose.

–

Mount and tighten screw



with the rubber bushing.

Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

F00307-11

–

Position the horn with the horn bracket.

–

Mount and tighten screws



with the collar bushings.

Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

K00596-11

–

Plug in connector



for the fuel pump.

–

Remove the wash cap set.

–

Thoroughly clean the plug-in connection of the fuel line using compressed air.

Info

Under no circumstances should dirt enter into the fuel line. Dirt in the fuel

line clogs the injection valve!

–

Lubricate the O-ring and connect plug-in connection



for the fuel line.

Info

Route the cable and fuel line at a safe distance from the exhaust system.

Finishing work

–

Mount the seat. (

p. 55)

–

Install the air filter box cover. (

p. 56)

12.33

Checking for chain dirt accumulation

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 63)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Бренды по названию

Популярные бренды