Husqvarna FE 450 Скачать руководство пользователя страница 16

Страница: 16 / 128

CONTROLS

6.1

Clutch lever

F00257-10

The clutch lever



is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2

Hand brake lever

F00258-10

The hand brake lever



is fitted on the right side of the handlebar.

The hand brake lever is used to activate the front brake.

6.3

Throttle grip

F00259-10

The throttle grip



is fitted on the right side of the handlebar.

6.4

Kill switch

F00260-10

Kill switch



is fitted on the left side of the handlebar.

Possible states

• Kill switch

in basic position

–

the ignition circuit is closed in this position and

the engine can be started.

• Kill switch

pressed

–

the ignition circuit is open in this position, the engine

goes out if it was running, or does not start if it was off.

6.5

Horn button

F00260-11

The horn button



is fitted on the left side of the handlebar.

Possible states

• Horn button

in neutral position

• Horn button

pressed

–

the horn is actuated in this position.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды