Husqvarna FE 450 Скачать руководство пользователя страница 108

Страница: 108 / 128

19 CLEANING, CARE

106

19.1

Cleaning the motorcycle

Note

Material damage

Components become damaged or destroyed if a pressure cleaner is used incorrectly.

The high pressure forces water into the electrical components, connectors, throttle cables, and bearings, etc.
Pressure which is too high causes malfunctions and destroys components.

–

Do not direct the water jet directly on to electrical components, connectors, throttle cables or bearings.

–

Maintain a minimum distance between the nozzle of the pressure cleaner and the component.
Minimum clearance

60 cm (23.6 in)

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

To maintain the value and appearance of the motorcycle over a long period, clean it regularly.
Avoid direct sunshine when cleaning the motorcycle.

401061-01

–

Close off the exhaust system to keep water from entering.

–

Remove coarse dirt particles with a gentle water jet.

–

Spray dirty parts with a normal commercial engine cleaner and then brush off with

a soft brush.

Info

Use warm water containing normal motorcycle cleaner and a soft sponge.
Never apply motorcycle cleaner to a dry vehicle; always rinse the vehicle

with water first.

–

After rinsing the motorcycle with a gentle spray of water, allow it to dry

thoroughly.

–

Remove the closure of the exhaust system.

Warning

Danger of accidents

Moisture and dirt impair the brake system.

–

Brake carefully several times to dry out and remove dirt from the brake

linings and the brake discs.

–

After cleaning, ride the vehicle a short distance until the engine warms up.

Info

The heat produced causes water at inaccessible locations in the engine

and on the brake system to evaporate.

–

After the motorcycle has cooled off, lubricate all moving parts and bearings.

–

Clean the chain. (

p. 63)

–

Treat bare metal (except for brake discs and the exhaust system) with a corrosion

inhibitor.

Preserving materials for paints, metal and rubber (

p. 118)

–

Treat all plastic parts and powder-coated parts with a mild cleaning and care

product.

–

Grease steering lock.

Universal oil spray (

p. 118)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды