Husqvarna FE 450 Скачать руководство пользователя страница 101

Страница: 101 / 128

17 TUNING THE ENGINE

17.4

Changing the mapping

Warning

Voiding of the government approval for road use and the insurance coverage

If the combination switch is installed,

the vehicle's approval for road use is invalidated.

–

Only operate the vehicle in closed-off areas remote from public road traffic if the combination switch is installed.

Info

The desired engine characteristic can be activated via the

MAP

button on the combination switch.

The setting most recently selected is activated again when restarting.
The traction control can also be activated in each mapping using the

button.

The mapping can also be changed during the ride.

H01180-10

Activating STANDARD mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

STANDARD

–

balanced response

H01180-11

Activating ADVANCED mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

ADVANCED

–

direct response

17.5

Adjusting the idle speed

Warning

Danger of accidents

The engine may go out spontaneously if the idle speed is set too low.

–

Set the idle speed to the specified value. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

F00448-10

–

Run the engine until warm.

The cold start button is deactivated

–

The cold start button is in its basic

position. (

p. 17)

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.

–

Always make sure there is sufficient ventilation when running the

engine.

–

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

–

Set the idle speed by turning idle speed adjusting screw



Guideline

Idle speed

1,800… 1,900 rpm

Tachometer (45129075000)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды