Husqvarna F2303U7 Скачать руководство пользователя

Страница: 76 / 171

12 SERVICE WORK ON THE CHASSIS

12.30

Removing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Preparatory work

–

Remove the air filter box cover. (

p. 69)

–

Remove the seat. (

p. 68)

–

Remove the right side cover. (

p. 73)

H03702-10

Main work

–

Unplug connector

of the fuel pump.

–

Clean quick release coupling

thoroughly with

compressed air.

Info

Under no circumstances should dirt enter into the fuel
line. Dirt in the fuel line clogs the injection valve!

H03703-10

–

Disconnect the quick release coupling.

Info

Remaining fuel may flow out of the fuel hose.

–

Mount wash cap set

Wash cap set (81212016100)

Содержание F2303U7












































































































































































Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды

Husqvarna F2303U7, Руководство пользователя

Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды