Husqvarna F2275U4 Скачать руководство пользователя

Страница: 74 / 162

12 SERVICE WORK ON THE CHASSIS

12.28

Installing the main silencer

S03561-11

Main work

–

Position the main silencer.

–

Mount screws

, but do not tighten yet.

–

Attach spring

Spring hook (50305017000C1)

–

Tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Install the right side cover. (

p. 71)

–

Mount the seat. (

p. 67)

–

Install the air filter box cover. (

p. 68)

12.29

Cleaning the spark arrestor

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Info

Soot particles accumulate on the screen of the spark arrestor over time.
This changes the performance characteristics.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 66)

–

Remove the right side cover. (

p. 70)

–

Remove main silencer. (

p. 71)

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды