Husqvarna F2275U4 страница 24 Скачать руководство пользователя

Страница: 24 / 162

6 CONTROLS

6.9

Turn signal switch

K00599-11

Turn signal switch

is fitted on the left side of the handlebar.

Possible states

Turn signal light off
Turn signal light, left, on

–

The turn signal switch is

pressed to the left. The turn signal switch returns to
the middle position after activation.
Turn signal light, right, on

–

The turn signal switch is

pressed to the right. The turn signal switch returns to
the middle position after activation.

To switch off the turn signal, press the turn signal switch toward
the switch housing.

6.10

Overview of indicator lamps

F00264-01

Possible states

The high beam indicator lamp lights up blue

–

The

high beam is switched on.
Malfunction indicator lamp lights up/flashes yellow

–

The OBD has detected an error in the vehicle elec-

tronics. Come safely to a halt, and contact an autho-
rized Husqvarna Motorcycles workshop.
The fuel level warning lamp lights up yellow

–

The

fuel level has reached the reserve mark.
Turn signal indicator lamp flashes green

–

The turn

signal is switched on.

6.11

Opening fuel tank filler cap

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Содержание F2275U4



































































































































































Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды

Husqvarna F2275U4, Руководство пользователя

Результаты поиска

Содержание F2275U4

Отзывы:

Похожие инструкции для F2275U4

Бренды по названию

Популярные бренды