manualshive.com logo in svg

Husqvarna F2275U4, Руководство пользователя, Страница: 125 / 162

Поделиться
Скачать
Husqvarna F2275U4 Скачать руководство пользователя страница 125

TUNING THE ENGINE 17

123

S03567-10

Main work

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

1

.

–

Loosen nut

2

.

–

Turn adjusting screw

3

in as far as possible.

–

Loosen nut

4

.

–

Push cold start button

6

all the way to the stop.

–

Turn adjusting screw

5

so that the cold start button moves

to the basic position when the throttle grip is turned to the
front.

–

Tighten nut

4

.

–

Turn adjusting screw

3

so that there is play in the throttle

cable at the throttle grip.
Guideline

Throttle cable play

3 … 5 mm (0.12 … 0.2 in)

–

Tighten nut

2

.

–

Slide on sleeve

1

.

–

Check the throttle grip for smooth operation.

Finishing work

–

Check the throttle cable play. (

p. 122)

17.3

Adjusting the characteristic map of the throttle response

Info

On the throttle grip, the characteristic map of the throttle response is changed by changing the guide
plate.
A guide plate with a different characteristic map is supplied.

A00368-10

Main work

–

Push back sleeve

1

.

–

Remove screws

2

and half-shells

3

.

–

Detach the throttle cables and take off the grip tube.

Содержание F2275U4



































































































































































Отзывы:

Нет отзывов