Husqvarna F2203V4 Скачать руководство пользователя

Страница: 96 / 166

13 BRAKE SYSTEM

F03509-10

–

Add brake fluid up to level

Guideline

Level

(brake fluid level

below reservoir rim)

5 mm (0.2 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 152)

–

Position cover

with membrane

–

Mount and tighten screws

Info

Use water to immediately clean up any brake fluid that
has overflowed or spilled.

13.7

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear
brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

402026-10

–

Disconnect spring

–

Move the foot brake lever back and forth between the end
stop and the contact to the foot brake cylinder piston and
check free travel

Guideline

Free travel at foot brake
lever

3 … 5 mm (0.12 … 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.
(

p. 95)

–

Reconnect spring

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды