Husqvarna F2203V4 страница 49 Скачать руководство пользователя

Страница: 49 / 166

TUNING THE CHASSIS 11

11.5

Adjusting the rebound damping of the shock absorber

Caution

Risk of injury

Parts of the shock absorber will move around if the shock absorber is detached incor-

rectly.
The shock absorber is filled with highly compressed nitrogen.

–

Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be
glad to help.)

F02303-10

–

Turn adjusting screw

clockwise up to the last perceptible

click.

–

Turn counterclockwise by the number of clicks correspond-
ing to the shock absorber type.
Guideline

Rebound damping

Comfort

17 clicks

Standard

15 clicks

Sport

13 clicks

Info

Turn clockwise to increase the damping; turn
counterclockwise to reduce damping when the shock
absorber rebounds.

11.6

Measuring the dimension of the rear wheel unloaded

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 54)

F03462-10

Main work

–

Position the sag gage in the rear axle and measure the
distance to marking

SAG

on the rear fender.

Sag gauge (00029090500)
Pin, sag scale (00029990010)

–

Note the value as dimension

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды