Husqvarna F2203V4 Скачать руководство пользователя

Страница: 128 / 166

17 TUNING THE ENGINE

126

17.4

Changing the mapping

Warning

Voiding of the government approval for road use and the insurance coverage

If the combination

switch is mounted, the vehicle’s road permit, if any, expires.

–

Only operate the vehicle in closed-off areas remote from public road traffic if the combination
switch is installed.

Info

The desired engine characteristic can be activated via the

MAP

button on the combination switch.

The setting most recently selected is activated again when restarting.
The traction control can also be activated in each mapping using the

button.

The mapping can also be changed during the ride.

H02889-01

Activating STANDARD mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

STANDARD

–

balanced response

H02886-01

Activating ADVANCED mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

ADVANCED

–

direct response

17.5

Adjusting the idle speed

Warning

Danger of accidents

The engine may go out spontaneously if the idle speed is set too low.

–

Set the idle speed to the specified value. (Your authorized Husqvarna Motorcycles workshop will be
glad to help.)

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды