Husqvarna F2203V4 страница 126 Скачать руководство пользователя

Страница: 126 / 166

17 TUNING THE ENGINE

124

F03510-10

Main work

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

–

Loosen nut

–

Turn adjusting screw

in as far as possible.

–

Loosen nut

–

Push cold start button

all the way to the stop.

–

Turn adjusting screw

so that the cold start button moves

to the basic position when the throttle grip is turned to the
front.

–

Tighten nut

–

Turn adjusting screw

so that there is play in the throttle

cable at the throttle grip.
Guideline

Play in throttle cable

3 … 5 mm (0.12 … 0.2 in)

–

Tighten nut

–

Slide on sleeve

–

Check the throttle grip for smooth operation.

Finishing work

–

Check the play in the throttle cable. (

p. 123)

17.3

Adjusting the characteristic map of the throttle response

Info

On the throttle grip, the characteristic map of the throttle response is changed by changing the guide
plate.
A guide plate with a different characteristic map is supplied.

F03511-10

Main work

–

Push back sleeve

–

Remove screws

and half-shells

–

Detach the throttle cables and take off the grip tube.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды