manualshive.com logo in svg

Husqvarna F2203V4, Руководство пользователя

Поделиться
Скачать
Husqvarna F2203V4 Скачать руководство пользователя страница 117

ELECTRICAL SYSTEM 15

115

15.8

Changing the headlight bulb

Note

Damage to reflector

 

Grease on the reflector reduces the light intensity.

Grease on the bulb will evaporate due to the heat and be deposited on the reflector.

–

Clean and degrease the bulbs before mounting.

–

Do not touch the bulbs with your bare hands.

Preparatory work

–

Remove the headlight mask with the headlight. (

p. 113)

H03753-10

Main work

–

Turn protection cap

1

together with the underlying bulb

socket counterclockwise all the way and remove it.

–

Pull bulb socket

2

of the position light out of the reflector.

F00361-10

–

Pull out headlight bulb

3

.

–

Insert the new headlight bulb.

Headlight (HS1 / Sockel PX43t) (

p. 147)

–

Insert the protection cap with the bulb socket into the reflec-
tor and turn it clockwise all the way.

Info

Ensure that O-ring

4

is seated properly.

–

Insert the bulb socket of the position light into the reflector.

Finishing work

–

Install the headlight mask with the headlight. (

p. 113)

–

Check the headlight setting. (

p. 116)

15.9

Changing the turn signal bulb (EU)

Note

Damage to reflector

 

Grease on the reflector reduces the light intensity.

Grease on the bulb will evaporate due to the heat and be deposited on the reflector.

–

Clean and degrease the bulbs before mounting.

–

Do not touch the bulbs with your bare hands.

Содержание F2203V4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды