manualshive.com logo in svg

Husqvarna F2201V1, Руководство пользователя

Поделиться
Скачать
Husqvarna F2201V1 Скачать руководство пользователя страница 83

SERVICE WORK ON THE CHASSIS 11

81

11.39

Checking the frame

K01114-01

–

Check the frame for damage, cracking, and deformation.
» If the frame shows signs of damage, cracking, or defor-

mation:

–

Change the frame.
Guideline

Repairs on the frame are not permitted.

11.40

Checking the link fork

401520-01

–

Check the link fork for damage, cracking, and deformation.
» If the link fork exhibits damage, cracking, or deformation:

–

Change the link fork.

Info

Always replace a damaged link fork. Repair of
the link fork is not authorized by Husqvarna
Motorcycles.

11.41

Checking the throttle cable routing

Preparatory work

–

Remove the air filter box cover. (

p. 65)

–

Remove the seat. (

p. 64)

–

Remove the right side cover. (

p. 70)

–

Remove the fuel tank.

(

p. 71)

V01552-01

Main work

–

Check the throttle cable routing.

Both throttle cables must be routed, side by side, on the
back of the handlebars and above the fuel tank bracket,
to the throttle valve body. Both throttle cables must be
secured behind the rubber strap of the fuel tank support.

» If the throttle cable is not routed as specified:

–

Correct the throttle cable routing.

Содержание F2201V1































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды