Husqvarna F2201V1 Скачать руководство пользователя страница 29

Страница: 29 / 158

PREPARING FOR USE 7

7.7

Preparing the vehicle for riding on wet and muddy circuits

M01274-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for Husqvarna Motor-
cycles accessories.

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 126)

–

Straighten the bent radiator fins carefully.

7.8

Preparing vehicle for high temperatures or slow riding

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is
operated frequently due to an excessively high sec-
ondary ratio.

–

Clean the chain.

Chain cleaner (

p. 146)

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

–

Check the coolant level. (

p. 110)

7.9

Preparing the vehicle for low temperatures or snow

M01274-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for Husqvarna Motor-
cycles accessories.

Содержание F2201V1































































































































































Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2201V1, Руководство пользователя

Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды