Husqvarna F2201V1 Скачать руководство пользователя страница 18

Страница: 18 / 158

6 CONTROLS

6.1

Clutch lever

A00985-10

The clutch lever

is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2

Hand brake lever

S01193-10

The hand brake lever

is fitted on the right side of the handle-

bar.
The front brake is engaged using the hand brake lever.

6.3

Throttle grip

V01558-10

The throttle grip

is fitted on the right side of the handlebar.

6.4

Stop button

S01194-10

The stop button

is fitted on the left side of the handlebar.

Possible states

• The stop button

is in the basic position

–

In this position,

the ignition circuit is closed and the engine can be started.

• Stop button

pressed

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a non-running
engine will not start.

Содержание F2201V1































































































































































Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2201V1, Руководство пользователя

Результаты поиска

Содержание F2201V1

Отзывы:

Бренды по названию

Популярные бренды