Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 77

Страница: 77 / 216

11 TUNING THE CHASSIS

–

Fit the rear fairing.

–

Install the air filter box.

–

Mount the side cover. (

p. 84)

–

Mount the seat. (

p. 83)

–

Remove the motorcycle from the work stand.

–

Check the static sag of the shock absorber. (

p. 70)

–

Adjust the rebound damping of the shock absorber. (

p. 68)

11.13

Handlebar position

V00495-10

The holes on the handlebar support are placed at a distance of



from the center.

Hole distance



3.5 mm (0.138 in)

The handlebar can be mounted in 2 different positions. In this way, the handlebar can be

mounted in the most comfortable position for the rider.

11.14

Adjusting the handlebar position

Warning

Danger of accidents

A repaired handlebar poses a safety risk.

If the handlebar is bent or straightened, the material becomes fatigued. The handlebar may break as a result.

–

Change the handlebar if the handlebar is damaged or bent.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды