Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 66

Страница: 66 / 216

11 TUNING THE CHASSIS

11.1

Fork/shock absorber

V00493-10

The fork and the shock absorber offer many options of adapting the chassis to your riding

style and the payload.

Info

To help you adapt the vehicle, we have summarized our findings in Table



. You

can find the table on the underside of the seat.

These adjustments should be understood as a guideline and should always be the basis

of your own personal suspension setting. Do not change the adjustments at random or by

more than ± 40 %, since otherwise the riding characteristics could deteriorate, particu-

larly at high speeds.

11.2

Adjusting the compression damping of the fork

Info

The hydraulic compression damping determines the fork suspension behavior.

V00506-10

–

Turn white adjusting screw



clockwise as far as it will go.

Info

Adjusting screw



is located at the upper end of the left fork leg.

The compression damping is located in left fork leg

COMP

(white adjusting

screw). The rebound damping is located in right fork leg

REB

(red adjusting

screw).

–

Turn counterclockwise by the number of clicks corresponding to the fork type.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды