Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 45

Страница: 45 / 216

PREPARING FOR USE

8.1

Advice on first use

Danger

Danger of accidents

A rider who is not fit to ride poses a danger to him or herself and others.

–

Do not operate the vehicle if you are not fit to ride due to alcohol, drugs or medication.

–

Do not operate the vehicle if you are physically or mentally impaired.

Warning

Risk of injury

Missing or poor protective clothing presents an increased safety risk.

–

Wear appropriate protective clothing such as helmet, boots, gloves as well as trousers and a jacket with protectors on all

rides.

–

Always wear protective clothing that is in good condition and meets the legal regulations.

Warning

Danger of crashing

Different tire tread patterns on the front and rear wheel impair the handling characteristic.

Different tire tread patterns can make the vehicle significantly more difficult to control.

–

Make sure that only tires with a similar tire tread pattern are fitted to the front and rear wheel.

Warning

Danger of accidents

Non-approved or non-recommended tires and wheels impact the handling characteristic.

–

Only use tires/wheels approved by Husqvarna Motorcycles with the corresponding speed index.

Warning

Danger of accidents

Reduced road grip with new tires.

–

New tires have a smooth rolling surface and therefore cannot provide full road grip. The entire rolling surface must be rough-

ened in the first 200 kilometers (124.3 miles) by moderate riding at alternating angles. The full grip levels are not achieved

until the tires have been run in.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды