Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 176

Страница: 176 / 216

18 SERVICE WORK ON THE ENGINE

174

F00589-10

–

Insert new oil filter



–

Lubricate the O-ring of the oil filter cover. Position oil filter cover



–

Mount and tighten screws



Guideline

Screw, oil filter cover

6 Nm (4.4 lbf ft)

–

Fill up with engine oil at the clutch cover.

Engine oil

1.70 l (1.8 qt.)

Engine oil (SAE 10W/50) (

p. 201)

Info

Too little engine oil or poor-quality engine oil results in premature wear of the

engine.

H01066-10

–

Mount and tighten oil filler plug



with the O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result

in unconsciousness and death.

–

Always make sure there is sufficient ventilation when running the engine.

–

Use an effective exhaust extraction system when starting or running the

engine in an enclosed space.

–

Start the engine and check that it is oil-tight.

Finishing work

–

Install the engine guard. (

p. 102)

–

Check the engine oil level. (

p. 168)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды