Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 171

Страница: 171 / 216

18 SERVICE WORK ON THE ENGINE

169

S01051-10

Main work

–

Check the engine oil level.

Info

After switching off the engine, wait one minute before checking the level.

The engine oil must be between marking



and marking



of the oil level viewer.

» If the engine oil level is below the



mark:

–

Add engine oil. (

p. 175)

» If the engine oil level is above the



mark:

–

Correct the engine oil level.

18.3

Changing the engine oil and oil filter, cleaning the oil screens

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

–

Wear suitable protective clothing and safety gloves.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable regula-

tions.

Info

Drain the engine oil while the engine is at operating temperature.

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды