Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 134

Страница: 134 / 216

14 WHEELS, TIRES

132

H01144-10

–

Check the tire age.

Info

The tire date of manufacture is usually contained in the tire label and is indi-

cated by the last four digits of the

DOT

number. The first two digits indicate

the week of manufacture and the last two digits the year of manufacture.
Husqvarna Motorcycles recommends that the tires be changed after 5 years at

the latest, regardless of the actual state of wear.

» If the tires are more than 5 years old:

–

Change the tires.

14.7

Checking the tire air pressure

Info

Low tire air pressure leads to abnormal wear and overheating of the tire.
Correct tire air pressure ensures optimal riding comfort and maximum tire service life.

400695-01

–

Remove the protection cap.

–

Check the tire air pressure when the tires are cold.

Tire air pressure, offroad, single rider

Front

1.5 bar (22 psi)

Rear

1.5 bar (22 psi)

Tire air pressure, road, solo

Front

1.8 bar (26 psi)

Rear

1.8 bar (26 psi)

Tire air pressure with passenger / fully loaded

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды