Husqvarna 550H EPOS Скачать руководство пользователя страница 24

Страница: 24 / 44

operation mode is selected and the START button is

pushed.

4.4.2 Select duration

The product goes back to the charging station and stays

for the selected park duration. Use the operation

selection to temporary stop an ongoing mowing cycle

and let the product to stay in the charging station.

4.4.3 Operating mode - Pause

When selecting

Pause

in the Automower

Connect app,

the product stop the current activity and pause. The

product is paused until either

Park

Start

is selected in

the Automower

Connect app.

4.5 To stop the product

Push the STOP button on top of the product.

The product stops and the blade motor stops.

Note:

When you push the START button again, the

product continues to operate in the same operating

mode as before.

4.6 To switch off the product

Push the STOP button on top of the product.

Enter the Automower

Connect app and connect

to the product with Bluetooth

short-range.

Note:

If the product is not connected to

Automower

Connect with Bluetooth

when

setting the Main switch to 0, the product is disabled

but not switched off. When the product is disabled

the motors are not allowed to run.

Set the Main switch to position 0.

WARNING:

Always switch off the

product using the Main switch if it requires

maintenance, or if the product must be

moved outside the work area.

4.7 To charge the battery

WARNING:

Only charge the product

using a charging station which is intended

for it. Incorrect use may result in electric

shock, overheating or leakage of corrosive

liquid from the battery.
In the event of leakage of electrolyte flush

with water and seek medical help if it comes

in contact with the eyes etc.

When the product is new or has been in storage for a

long period, the battery can be empty, charge the

battery before you start the product.
1.

Set the Main switch to position

Put the product in as far as possible in the

charging station. Make sure that the product and

the charging station is connected. Refer to contact

and charging strips in

Product overview on page 5

Make sure that the charging is in progress in the

Automower

Connect app.

24 - Operation

1619 - 002 - 19.01.2021

Содержание 550H EPOS












































Результаты поиска

Содержание 550H EPOS

Отзывы:

Husqvarna 550H EPOS, Руководство оператора, Страница: 24 / 44

Результаты поиска

Содержание 550H EPOS

Отзывы: