Husqvarna 520iRX Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

Husqvarna 520iRX Скачать руководство пользователя страница 22

• To attach, tighten the lock nut in the opposite

direction to the direction of rotation of the cutting

attachment.

• To remove the locking nut, undo the lock nut in the

same direction as the cutting attachment rotates.

• To loose and tighten the locknut, use a socket

spanner with a long shaft. The arrow in the picture

shows the area where you should operate the socket

spanner.

WARNING: When you loose and tighten

the locknut there is a risk of injury from

the teeth of the saw blade. You should

therefore always ensure that your hand

is shielded by the blade guard when you

do this.

Note: Make sure that you can not turn the locknut by

hand. Replace the nut if the nylon lining does not have a

resistance of a minimum of 1.5 Nm. The nut should be

replaced after it has been put on approximately 10

times.

To adjust the harness

WARNING: The product must always be

correctly attached to the harness. Do not

use a defective harness.

1. Put on the harness.
2. Connect the product to the harness.
3. Adjust the harness for the best work position.
4. Adjust the side straps to make the product weigh

equally on your shoulders.

5. Adjust the harness until the cutting attachment is

parallel to the ground.

6. Let the cutting attachment lightly touch the ground.

Adjust the harness clamp to balance the product

correctly.

Note: If you use a grass blade, it must balance

approximately 10 cm /4 in above the ground.

Operation

Introduction

WARNING: Read and understand the safety

chapter before you use the product.

To examine the product before

operation

• Examine the motor for dirt and cracks. Use a brush

to remove grass and leaves from the engine. Wear

protective gloves when necessary.

• Make sure that the trimmer head is fully attached to

the product.

• Do the safety inspections, maintenance and

servicing that are given in this manual.

• Make sure that the product is not damaged. Examine

that all nuts and screws are tight.

22

757 - 001 - 24.10.2018

«
...
20
21
22
23
24
...
»

Содержание 520iRX





































Отзывы:

Нет отзывов