manualshive.com logo in svg

Husqvarna 326HD60 Series, Руководство оператора, Страница: 22 / 28

Поделиться
Скачать
Husqvarna 326HD60 Series Скачать руководство пользователя страница 22

22 – English

TECHNICAL DATA

Technical data

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under 
various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.

Technical data

326HD60

326HD75

Engine

Cylinder displacement, cu.in/cm

3

1,55/25,4

1,55/25,4

Cylinder bore, inch/mm

1,34/34

1,34/34

Stroke, inch/mm

1,10/28

1,10/28

Idle speed, rpm

2700

2700

Recommended max. fast idle speed, rpm

10500-12500

10500-12500

Max. engine output, acc. to ISO 8893

0,9/9000

0,9/9000

Catalytic converter muffler

Yes

Yes

Speed-regulated ignition system

Yes

Yes

Ignition system

Manufacturer/type of ignition system

Walbro MB

Walbro MB

Spark plug

Champion RCJ 6Y

Champion RCJ 6Y

Electrode gap, inch/mm

0,02/0,5

0,02/0,5

Fuel and lubrication system

Manufacturer/type of carburetor

Zama C1Q

Zama C1Q

Fuel tank capacity, US pint/litre

1,0/0,5

1,0/0,5

Weight

Weight without fuel, Lbs/kg

12,6/5,7

13,2/6,0

Sound levels

(see note 1)

Equivalent noise pressure level at the operator’s ear, 
measured according to EN/ISO 11806 and ISO 7917, 
dB(A), min./max.:

98

98

Vibration levels

Vibration levels at handles, measured according to EN/
ISO 11806 and ISO 7916, m/s

2

Idle speed, rear/front handles:

2,8/2,8

3,7/3,7

Max. speed, rear/front handles:

5,7/6,4

4,9/4,5

Blades

Type

Double sided

Double sided

Length, mm

600

735

Blade speed, cuts/min

4695

4695

Содержание 326HD60 Series





























Отзывы:

Нет отзывов