Husqvarna 2016 FE 250 Скачать руководство пользователя страница 45

Страница: 45 / 124

12 SERVICE WORK ON THE CHASSIS

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on

the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them

with brake cleaner when necessary.

–

Clean and oil the dust boots and inner fork tubes of both fork legs.

Universal oil spray (

p. 114)

–

Press the dust boots back into their normal position.

–

Remove excess oil.

Finishing work

–

Install the fork protector. (

p. 44)

–

Remove the motorcycle from the lift stand. (

p. 42)

12.5

Removing the fork legs

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the headlight mask with the headlight. (

p. 85)

–

Raise the motorcycle with a lift stand. (

p. 42)

–

Remove the front wheel.

(

p. 77)

H00177-10

Main work

–

Remove screws



and take off the clamp.

–

Remove the cable tie(s).

–

Remove screws



and take off the brake caliper.

–

Allow the brake caliper and brake line to hang tension-free to the side.

H00179-10

–

Loosen screws



. Take out the left fork leg.

–

Loosen screws



. Take out the right fork leg.

12.6

Installing the fork legs

402556-10

Main work

–

Position the fork legs.

Bleeder screws



are positioned toward the front.

Info

The compression damping is located in left fork leg

COMP

(white

adjusting screw). The rebound damping is located in right fork leg

REB

(red adjusting screw).
Grooves are milled into the side of the upper end of the fork legs. The sec-

ond milled groove (from the top) must be flush with the top edge of the

upper triple clamp.

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды