Husqvarna Viking Rose 605 страница 57 Скачать руководство пользователя | Manualshive

Страница: 57 / 64

background image

Instruction book Rose

57

Incorrect stitch

If the machine does not sew the
stitch indicated by the display, it is
possible that the electronics have
been disturbed in some way, per-
haps by a short power cut or electri-
cal disturbance. Shut off the main
switch, wait a few seconds and try
again. If the fault remains, contact
your dealer.

The stitch is too loose - fabric
layers not held together

The thread tension is far too loose.
Page 14 shows how to adjust the
thread tension.

Fault-finding

Machine runs sluggishly

Dirt or lint has built up under the
stitch plate. Loosen the plate and
brush clean between the feed teeth
and in the bottom area. See page 55.

Balance setting for buttonhole

Balance can only be set if a button-
hole is selected. Press the buttons

and

until the letters

BAL

are flashing to the left on the dis-
play. In place of the stitch length
indication a balance indication is
shown. When you wish to increase
the density of the right column,
press stitch length button (-). When
you wish to decrease the density,
press stitch length button (+). The
balance can be set between -5 to +5.
The balance indication on the dis-
play will change in steps fo each
touch. When you select another
stitch, the display goes back to show
the sitch length indication. The
machine always retains the last
made balance setting.

Main motor does not work

The electronic overload protector
may have switched off. Shut off the
main switch, wait about a minute.
Then switch on the machine.

The sewing and embroidery
machine screen does not respond
to touch

The socket on the back of the
machine where the embroidery unit
is connected can be sensitive to
static electricity when the
embroidery unit is not connected. If
the sewing machine screen does not
respond to touch, turn the machine
off and back on again. If this
persists, contact your authorized
Husqvarna Viking retailer.

Expert assistance

Have your machine "tuned up"
regularly by your dealer. If you have
followed the preceding points and
still do not get satisfactory results,
you should contact the dealer where
you bought the machine. When the
machine is being checked, it is a
great help if it can be test sewn
under as similar conditions as
possible as when you used it.
Remember to take a sewing sample
along with you, preferably of the
fabric and with the thread you
intend to use.
A sewing sample will often give
much better information than words.

Non-original Parts and
Accessories

The warranty does not cover any
defect or damage caused by use of
non-original accessories or parts.

F

ault-finding

«
...
55
56
57
58
59
...
»

Содержание Rose 605

































































Отзывы:

Нет отзывов

Похожие инструкции для Rose 605

Бренд: Janome Страницы: 8

CHARGER 2022 ABLT

Бренд: NSS Страницы: 16

Бренд: Cameo Страницы: 40

Бренд: Amplicom Страницы: 4

Бренд: Kärcher Страницы: 39

Бренд: handi quilter Страницы: 69

Бренд: Singer Страницы: 53

TRIDENT T26 SC PLUS

Бренд: Hillyard Страницы: 28

Бренд: Necci Страницы: 39

Бренд: ELNA Страницы: 61

Бренд: Singer Страницы: 67

Fitness E-ST 5090

Бренд: Star Trac Страницы: 28

Бренд: Tennant Страницы: 155

Бренд: JUKI Страницы: 40

Бренд: JUKI Страницы: 140

Бренд: JUKI Страницы: 100

Бренд: Kenmore Страницы: 90

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды