background image

Form # 41475-01   Rev. 1-23-2001

Hunter Fan Company
Remote Ceiling Fan
& Light Control

®

Transmitter Model:  85095

Transmitter Battery:  12 V, Type 23A, MN-21 or equivalent

Receiver Model:  85069

Ratings:  120 VAC, 60 Hz,1.0 Amp Fan

Receiver Weight:  8 oz.

300 Watts incandescent light

Notes:

1.

This device complies with Part 15 of the FCC Rules. Operation is sub-
ject  to  the  following  two  conditions:  (1)  this  device  may  not  cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

2.

This equipment has been tested and found to comply with the limits
for  a  Class  B  digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.
These  limits  are  designed  to  provide  reasonable  protection  against
harmful interference in a residential installation. This equipment gen-
erates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  in-
stalled and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

3.

For use only with electrically reversible ceiling fans rated at 1.0 amp or
less, and fan incandescent light kits rated at 300 watts or less.

4.

Not for use with shaded-pole or non-reversible motors. Not recom-
mended for use with the Hunter Original®.

Before Installing the Control:

1.

Use the pull-chain switch to set the fan speed to the HIGH position
before installation. Do not use the pull-chain to change the fan speed
after installation, as damage to your ceiling fan or control may result.
The speed of the fan should only be changed by the control.

2.

Set the ceiling fan light kit to the ON position before installation. The
light level should only be changed by the control.

Receiver Installation:

1.

Disconnect power to the ceiling fan and light kit at the main electric
panel. Remove fuse or move circuit breaker to the OFF position.  Turn
off wall switch.

2.

IMPORTANT! Before installing this control, change the factory default
jumper switch settings to your own unique code. Refer to Figure 1.
Using small pliers or tweezers, pull out one or more of the three jumper
swtiches  by  clamping  on  the  small  metal  strip.    Place  the  jumper
switches in the desired spots.  Be sure the jumper switch positions of
the transmitter and receiver match, or the ceiling fan will not func-
tion.  Select different combinations of jumper switches to prevent mis-
operation due to other remote control fans, garage door openers, etc.

3.

Install the ceiling fan according to its instructions, up to the point of
making the electrical connections.

4.

Use the 2 large wire nuts supplied to connect the receiver and house
wiring, then use the 3 small wire nuts supplied to connect the receiver
and ceiling fan wiring. Refer to the Wiring Diagram in Figure 2.

Caution: Risk of Electrical Shock!

All wiring must be performed in accordance with national and local electri-
cal  codes.  If  you  are  unfamiliar  with  the  wiring  codes,  you  should  use  a
qualified electrician.

To  avoid  overheating  and  possible  damage  to  other  equipment,  do  not
install to control a receptacle, fluorescent light fixture, motor operated ap-
pliance, or transformer-supplied appliance. Use only to control one paddle-
blade ceiling fan and incandescent light fixture.

Read and Save these Instructions

Ceiling Plate

Receiver

Canopy

Figure 3 - Installing Receiver

Jumper
Switch

Transmitter

Jumper
Switch

Back

Receiver

Back

Figure 1 - Jumper Switches

Figure 2 - Wiring Diagram

Light

Kit

Black /
White

Black

White

Fan

Common

Antenna

120 V AC
Power
In

White Main

Black Main

5.

Install receiver as shown in Figure 3.  Line up slots on the receiver with
the ceiling plate.  Be sure to push wire connections from the ceiling
back up through the hole in the ceiling pate.  Wires attaching from
the ceiling plate to the fan should be placed inside the canopy under
the receiver.  Once the receiver is installed, continue with the appro-
priate instructions from the fan installation manual to finish installing
the fan.

Отзывы: