Hunter 28537 Скачать руководство пользователя

Страница: 9 / 12

Hunter Fan Company

41888-01 • 02/01/05

Hunter Fan Company

6 • Assembling the Blades

Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).

6-1. Your fan may include blade grommets. If your fan has grommets,

insert them by hand into the holes on the blades.

6-2. Attach each blade to a blade iron using three blade assembly

screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.

6-3. Remove the blade mounting screws and rubber shipping bumpers

from the motor.

6-4. For each blade, insert one blade mounting screw through the

blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.

Step 6-1 (Detail)

Blade Assembly

Screws

Use with grommet

Use without grommet

Blade Mounting

Screw

Grommet

Steps 6-1 – 6-2

Step 6-4

Содержание 28537













Результаты поиска

Содержание 28537

Отзывы:

Похожие инструкции для 28537

Бренды по названию

Популярные бренды

Hunter 28537, Руководство по установке и эксплуатации

Результаты поиска

Содержание 28537

Отзывы:

Похожие инструкции для 28537

Бренды по названию

Популярные бренды