Maintenance
If your boat remains in the water for long periods of time, algae and other
marine growth can reduce the effectiveness of the transducer. Periodically
clean the face of the transducer with hot water.
If your boat remains out of the water for a long period of time, it may take
some time to wet the transducer after it is returned to the water. Small air
bubbles can cling to the surface of the transducer and interfere with proper
operation. These bubbles will dissipate with time, or you may wipe the face of
the transducer with your fingers after the transducer is in the water.
1-Year Limited Warranty
We warrant the original retail purchaser that products made by Humminbird
have been manufactured free from defects in materials and workmanship.
This warranty is effective for one year from the date of original retail purchase.
Humminbird products found to be defective and covered by this warranty will
be repaired or replaced free of charge at Humminbird’s option and returned to
the customer freight prepaid. Humminbird’s sole responsibility under this
warranty is limited to the repair or replacement of a product that has been
deemed defective by Humminbird. Humminbird is not responsible for charges
connected with the removal of such product or reinstallation of replaced or
repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product
installation and operation instructions;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird.
Please retain your original receipt as a proof of the purchase date. This will be
required for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE
THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN
DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO
EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not
apply to you. You may also have other rights, which vary from state to state.
Humminbird Service Policy
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
After the original warranty period, a standard flat rate service charge will
be assessed for each repair (physical damage and missing parts are not
included). Any repairs made after the original warranty will be warranted
for an additional 90 days after service has been performed by our factory
technicians. You can contact Humminbird Customer Service or visit our
Web site to verify the flat rate repair fee for your product (visit the Product
Support section):
http://www.humminbird.com
We reserve the right to deem any product unserviceable when
replacement parts are no longer available or impossible to obtain. This
Service Policy is valid in the United States only. This applies only to
Humminbird products returned to our factory in Eufaula, Alabama. This
Service Policy is subject to change without notice.
DOMESTIC (USA) CUSTOMERS:
PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE
For all technical issues please call
1-800-633-1468
or visit
humminbird.com
, click
SUPPORT.
Please reference product serial number and
model number when contacting Humminbird.
Overview
Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from
your Humminbird® accessory.
Supplies:
In addition to the hardware supplied with your transducer, you will need a drill, a small drill bit for a pilot
hole, a 1 1/8" hole saw, a level, marine-grade silicone sealant, a Phillips-head screwdriver, and dielectric grease.
Customer Service:
To purchase additional equipment, or if you find that any items are missing from your installation
kit, visit our Web site at
humminbird.com
or call us at
1-800-633-1468
.
Installation
Perform the procedures in the following sections to install the transducer on your boat.
1.
Testing the Transducer Prior to Installation
Prior to installation, test the transducer to make sure that no damage occurred during shipping.
1. Connect the transducer cable connector to the control head port or black box sonar, depending on your system
configuration.
2. Power on the control head. Select a sonar view to display on-screen.
3. Hold the transducer in the water over the side of the boat to confirm proper operation. If the transducer is working
properly, you should be able to see the bottom on the control head display. The bottom image should be relatively
strong and there should be detailed structure on the display.
4. After confirming proper operation, power off the control head, and unplug the transducer cable connector from
the control head or black box sonar.
2.
Locating the Transducer Mounting Position
Outside the boat,
the best location for the transducer will be aft midship, as close to the centerline of the boat as
possible. The transducer should be mounted forward of the propellers on inboard boats, and separated adequately
from other transducers, strakes, rivet lines, or other protrusions. Make sure that there is nothing in front, behind, or to
the side of the transducer that is closer than 12".
WARNING!
Do NOT install the transducer in line with the engine intake.
Inside the boat,
there must be room to access the mounting location for installation and cable routing.
Deadrise:
Another consideration is the angle of deadrise. The transducer, when mounted, should point straight down.
If the selected mounting location has a hull deadrise of 8 degrees or more, the included leveling block should be used
to level the transducer housing and direct the sonar signal straight down. If you need to use the leveling block, make
sure that the inside surface of the hull is smooth enough to seat the leveling block securely.
NOTE:
If you cannot find a location that will work for your application, find a different transducer by visiting the FAQ
(Frequently Asked Questions) section of our Web site at
humminbird.com
or by calling Humminbird Customer Service
at
1-800-633-1468
.
NOTE:
This type of transducer installation is not recommended for trailerable boats.
NOTE:
This transducer requires drilling a hole in the hull of the boat; therefore, installation should be performed by a
qualified marine technician.
Thru-Hull Installation
Deadrise Angle
Preferred Mounting Location
Plastic Thru-Hull Transducer
1
530758-5_B
Areas of Possible Turbulence
Rivets
Transom
Strakes
Hull
Plastic Thru-Hull Transducer
6
530758-5_B
Plastic Thru-Hull Transducer
5
530758-5_B
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
NOTE:
Please do not return your Humminbird to the store for service.
Please have your product model name and serial number available before
calling the factory. If you contact the factory by e-mail, please include your
product model name and serial number in the e-mail, and use Request for
Repair Authorization Number for your e-mail subject header. You should
include your Repair Authorization Number in all subsequent communications
about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from Humminbird Customer
Service.
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of purchase).
• Return product freight prepaid to Humminbird, using an insured carrier
with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from Humminbird Customer
Service.
• Include payment in the form of credit card number and expiration date,
or a money order. Please do not send cash.
• Tag product with your name, street address, phone number and your
assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird, using an insured carrier
with delivery confirmation.
Contact Humminbird
Web site
humminbird.com
Telephone
1-800-633-1468
Direct Shipping
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING!
This device should not be used as a navigational aid to prevent
collision, grounding, boat damage, or personal injury. When the boat is moving,
water depth may change too quickly to allow time for you to react. Always operate
the boat at very slow speeds if you suspect shallow water or submerged objects.
WARNING!
Disassembly and repair of this electronic unit should only be performed
by authorized service personnel. Any modification of the serial number or attempt to
repair the original equipment or accessories by unauthorized individuals will void the
warranty.
WARNING!
This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
ENVIRONMENTAL COMPLIANCE STATEMENT:
It is the intention of Johnson
Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating in
compliance with known and applicable environmental regulations, and a good
neighbor in the communities where we make or sell our products.
WEEE DIRECTIVE:
EU Directive 2002/96/EC “Waste of Electrical and Electronic
Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers
of consumer electronics in the European Union. The WEEE Directive requires the
producer of consumer electronics to take responsibility for the management of waste
from their products to achieve environmentally responsible disposal during the
product life cycle.
WEEE compliance may not be required in your location for electrical & electronic
equipment (EEE), nor may it be required for EEE designed and intended as fixed or
temporary installation in transportation vehicles such as automobiles, aircraft, and
boats. In some European Union member states, these vehicles are considered
outside of the scope of the Directive, and EEE for those applications can be
considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not
be disposed of with other household refuse. It must be disposed of and
collected for recycling and recovery of waste EEE. Johnson Outdoors
Marine Electronics, Inc. will mark all EEE products in accordance with the
WEEE Directive. It is our goal to comply in the collection, treatment, recovery, and
environmentally sound disposal of those products; however, these requirements do
vary within European Union member states. For more information about where you
should dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer or
distributor from which your product was purchased.
NOTE:
Operations manuals are provided on the CD included with your Humminbird
control head, or you can download Humminbird manuals from our Web site at
humminbird.com
.
© 2014 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
Plastic_Thru-Hull_Transducer_IG_530758-5_B.qxp:530758-3_B 7/7/14 1:20 PM Page 1
