background image

Page 11                

 

 

 

 

 

 

 

                            Page 12 

SCAN

Indicate the current work at the scan mode. 

DSC

DSC capability is available. 

Battery Low indicates vessel battery voltage is low. 

A B

Channel suffix, if applicable. 

ATIS

Enable for use In European in inland waterway other wise blank 

Dot Matrix

Display indicates special conditions or radio functions. 

 

3 INSTALLATION 

3.1 SUPPLIED 

ACCESSORIES 

Manufacturer supplies you the following accessories as soon as you purchase 
this ***** radio: 

 

Mounting gimbals (1 set) 

 

Power Supply Cable and External Speaker Connection Cable (1 set) 

 

Mounting Knob (2 pcs) 

 

Wall Hanger (1 pcs) 

 

GPS Connection Cable (1 set) 

 

Self-tapping Screw for Fixing Mounting Gimbals (4 pcs) 

 

Flat Screw for Fixing Mounting Gimbals (4 pcs) 

 

Plain Washer (4 pcs) 

 

Spring Washer (4 pcs) 

 

Nut (4 pcs) 

 

Self-tapping Screw for Fixing Wall Hanger (2 pcs) 

 

Flat Screw for Fixing Wall Hanger (2 pcs) 

 

Plain Washer (2 pcs) 

 

Spring Washer (2 pcs) 

 

Nut (2 pcs) 

 

 

3.2 LOCATION

 

To more conveniently and efficiently use your marine radio, find a mounting 
location that: 

  Is far enough from any devices like devices to avoid any interference 

caused by the speaker magnet in your radio during their operation; 

 

Provides accessibility to the front panel controls; 

 

Allows connection to a power supply and an antenna; 

 

Has free space nearby for installation of a handset hanger; 

 

Where the antenna can be mounted at least 3 feet from radio. 

 

3.3 CONNECTIONS 

POWER SUPPLY 

You radio should be powered by a 13.8VDC power supply. Red cable is for 
positive pole and the thicker black one is for negative pole. 

EXTERNAL SPEAKER 

If needed, you can connect your radio to an external speaker with the supplied 
connection cable. White cable is for positive pole and the thinner black one is for 
negative pole. 

GPS EQUIPMENT 

When your marine radio *** is connected by the GPS cable to a GPS equipment, 
it can obtain the information of both its current location (longitude and latitude) 
and the local GMT.  
 

GPS CABLE 

 

NMEA IN (+) from GPS navigation receiver, pin3. Yellow. 

 

NMEA IN (-) from GPS navigation receiver, pin4. Green. 
NEMA 0183 Version (1.5 to 3.0) input Sentences: 

 

The sentences GLL, GGA, RMS, GNS shall be recognized. 
Note: never short wires. This may lead to malfunctions. 
Connecting: GPS cable round plug to radio and the wire of yellow and  
the green connect to GPS navigation receiver. 

 

 

 

 
 
 
 
 
 

To VHF255S.DSC

ORANGE

GREEN

YELLOW

BLACK

Содержание VHF255S-DSC
























Отзывы: