Hughes HN9400 Скачать руководство пользователя страница 47

Страница: 47 / 134

If you plan to use an antenna pointing tool, select

DAPT

OPI

, or

N/A

(for none) from the

Antenna Pointing Tool

drop-down list.

For Ka-band select DAPT; for Ku-band a DAPT or OPI may be used.

Click

Next

Note:

There is no verification screen when you manually enter the satellite parameters.

Entering radio parameters

On the Receive LNB Selection screen, select the installed LNB from the Receive LNB
drop-down list (

Figure 22: Receive LNB Selection screen—two variations

on page 36).

The list of LNBs you see depends on the how the router is configured, based on its

sbc.cfg

file.

Select the LNB option that matches the part number or other identifier on the installed LNB.
If you cannot find the LNB part number or identifier, refer to the LNB illustrations in

LNB

selection reference

on page 109 for guidance. If you are not sure which LNB option to select,

contact Installer Support.

Make sure you select the correct LNB. If you select the wrong

LNB, the satellite router will not work.

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Chapter 4

Commissioning the satellite router

Содержание HN9400







































































































































Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды

Hughes HN9400, Руководство по установке

Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды