Huber Pilot ONE Unichiller 00 eo Series страница 83 Скачать руководство пользователя

Страница: 83 / 86

Shutting down

Chapter 8

OPERATION MANUAL

V2.2.0en/09.08.21//17.12

Unichiller® eo Desktop

8.6

Uninstalling an external application

PROCEDURE



Disconnect the external application from the temperature control unit.

8.7

Packing

Always use the original packaging!

→

Page 24, section

»Unpacking«

8.8

Shipping

Temperature control unit transported in a horizontal position
DAMAGE TO THE COMPRESSOR



Only transport the temperature control unit in an upright position.

Temperature control unit transported incorrectly
PROPERTY DAMAGE



Do not transport by truck on the castors or feet.



Comply all requirements in this section to avoid damage to the temperature control unit.

Transport using the lugs, if fitted, on the top of the temperature control unit. Do not transport the

temperature control unit alone and without aids.

▪

Always use the original packaging for transportation.

▪

Indicate the upright transport position with arrows on the packaging.

▪

Always transport the temperature control unit upright on a pallet!

▪

Protect attachments from damage during transportation!

▪

During transport, place the temperature control unit on squared timber to protect the cast-

ers/feet.

▪

Secure with tensioning belts/lashing straps that are suitable for the weight.

▪

Additionally secure (depending on model) with plastic film, cardboard and straps.

Pallet with squared

timber for free-

standing units

Содержание Pilot ONE Unichiller 00 eo Series























































































Результаты поиска

Содержание Pilot ONE Unichiller 00 eo Series

Отзывы:

Похожие инструкции для Pilot ONE Unichiller 00 eo Series

Бренды по названию

Популярные бренды

Huber Pilot ONE Unichiller 00 eo Series, Руководство пользователя

Результаты поиска

Содержание Pilot ONE Unichiller 00 eo Series

Отзывы:

Похожие инструкции для Pilot ONE Unichiller 00 eo Series

Бренды по названию

Популярные бренды