IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.
Part No...........................................
93084892
Page 1 of 6
With representatives offices in principal cities throughout North America.
Copyright , revision, All Rights Reserved - Printed in U.S.A.
701 Millennium Blvd • Greenville, SC 29607
2017 12/26/17
w
w
w
.p
re
s
c
o
lit
e
.c
o
m
•
P
re
s
c
o
lit
e
T
o
ll
F
re
e
T
e
c
h
n
ic
a
l S
u
p
p
o
rt
1
.8
8
8
.P
R
S
.4
T
E
C
•
H
o
u
rs
: 8
a
m
-
5
p
m
E
T
In
s
tr
u
c
tio
n
S
h
e
e
t
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, MAKE CERTAIN THAT THE POWER SUPPLY IS OFF
BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Make sure to read and fully understand these instructions before attempting to install this product.
1. Before the ceiling is finished, run the appropriate line voltage
(and dimming control wiring if applicable) to the approximate
location where the AB2 fixture will be installed.
2. After the ceiling material is installed and finished, make the
ceiling cutout using a 2-7/8” hole saw to cut an opening for
the AB2 downlight. Because of the small reflector flange on
the AB2, the accuracy of this hole is critical. Even a 3” hole
saw may leave a ceiling cutout too large to be completely
hidden after installation.
3. Pull the wiring (installed earlier) below the ceiling, slide the
J-tube cover open (keeping it on the conduit) and connect
the wiring to the J-tube through the open 1/2" knockout. A
3/8” flex conduit duplex connector may be used to easily
daisy-chain the fixtures together. For single installations and
end-of-run applications, a standard 1/2” knockout connector
can be used.
Because the AB2 features dimming capability, be sure to
make any low voltage wiring connections in this step. When
wiring for dimming, the low voltage wiring installs through
the adjoining 1/2” knockout. A second 3/8” flex conduit duplex
connector may be used in this knockout where applicable.
4. After the appropriate connections have been made, simply
slide the J-tube closed until it locks in place with the spring on
opposite ends of the assembly.
WARNING: Do not pinch wires between J-Tube cover
and endplates!
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY INSTALLED WIRING ON THE FIXTURE. SAFETY
AND PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
KEEP THESE INSTALLATION INSTRUCTIONS!
INSTALLATION INSTRUCTIONS:
AB2LED
2-7/8" HOLE SAW
Fig. 1
Fig. 2
Fig. 3
