MOUNTING
OPERATION
Hubbell Lighting, Inc. Doc. No. 93059813
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
PAGE 3
FIGURE 7
FIGURA 7
T-SLOT
FASTENER
NLCA1
SECURING THE FIXTURE (See Figure 7 and Figure 8):
1. Aircraft cable can be used to secure the fixture to a TRUSS or
framework.
2. NLCA1 is a single point cable with a ¼-20 threaded stud. This
is the same thread that is on the T-SLOT fastener. The NLCA1
can be used for mounting single fixtures.
3. NLCA2 is a double point “Y” cable system that can be used for
different configurations.
FIGURE 8
FIGURA 8
POWERING THE FIXTURE(S) (See Figure 9):
1. Attach power cord to POWER IN panel connector.
2. An INTERCONNECT cord can be used to power multiple
fixtures or “DAISY CHAIN” fixtures together. Connect NO
MORE than
16 fixtures
on one power drop.
INTERCONNECT
CORD
POWER CORD
93059813_A_HIL0093 1/15
NutriLED SERIES
LED HORTICULTURAL LIGHT
WARNINGS
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
•
Disconnect power before installing or servicing.
•
The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
•
Protect all wiring connections with approved insulators rated 600V. 150OC.
•
Line voltage must be 120V – 277V to match Fixture voltage requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
•
Upon receipt of this Fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held accountable.
Hubbell Lighting, Inc. Doc. No. 93059813
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
PAGE 3
FIGURE 7
FIGURA 7
T-SLOT
FASTENER
NLCA1
SECURING THE FIXTURE (See Figure 7 and Figure 8):
1. Aircraft cable can be used to secure the fixture to a TRUSS or
framework.
2. NLCA1 is a single point cable with a ¼-20 threaded stud. This
is the same thread that is on the T-SLOT fastener. The NLCA1
can be used for mounting single fixtures.
3. NLCA2 is a double point “Y” cable system that can be used for
different configurations.
FIGURE 8
FIGURA 8
POWERING THE FIXTURE(S) (See Figure 9):
1. Attach power cord to POWER IN panel connector.
2. An INTERCONNECT cord can be used to power multiple
fixtures or “DAISY CHAIN” fixtures together. Connect NO
MORE than
16 fixtures
on one power drop.
INTERCONNECT
CORD
POWER CORD
Hubbell Lighting, Inc. Doc. No. 93059813
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
PAGE 3
FIGURE 7
FIGURA 7
T-SLOT
FASTENER
NLCA1
SECURING THE FIXTURE (See Figure 7 and Figure 8):
1. Aircraft cable can be used to secure the fixture to a TRUSS or
framework.
2. NLCA1 is a single point cable with a ¼-20 threaded stud. This
is the same thread that is on the T-SLOT fastener. The NLCA1
can be used for mounting single fixtures.
3. NLCA2 is a double point “Y” cable system that can be used for
different configurations.
FIGURE 8
FIGURA 8
POWERING THE FIXTURE(S) (See Figure 9):
1. Attach power cord to POWER IN panel connector.
2. An INTERCONNECT cord can be used to power multiple
fixtures or “DAISY CHAIN” fixtures together. Connect NO
MORE than
16 fixtures
on one power drop.
INTERCONNECT
CORD
POWER CORD
Hubbell Lighting, Inc. Doc. No. 93059813
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
PAGE 3
FIGURE 7
FIGURA 7
T-SLOT
FASTENER
NLCA1
SECURING THE FIXTURE (See Figure 7 and Figure 8):
1. Aircraft cable can be used to secure the fixture to a TRUSS or
framework.
2. NLCA1 is a single point cable with a ¼-20 threaded stud. This
is the same thread that is on the T-SLOT fastener. The NLCA1
can be used for mounting single fixtures.
3. NLCA2 is a double point “Y” cable system that can be used for
different configurations.
FIGURE 8
FIGURA 8
POWERING THE FIXTURE(S) (See Figure 9):
1. Attach power cord to POWER IN panel connector.
2. An INTERCONNECT cord can be used to power multiple
fixtures or “DAISY CHAIN” fixtures together. Connect NO
MORE than
16 fixtures
on one power drop.
INTERCONNECT
CORD
POWER CORD
Hubbell Lighting, Inc. Doc. No. 93059813
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
PAGE 3
FIGURE 7
FIGURA 7
T-SLOT
FASTENER
NLCA1
SECURING THE FIXTURE (See Figure 7 and Figure 8):
1. Aircraft cable can be used to secure the fixture to a TRUSS or
framework.
2. NLCA1 is a single point cable with a ¼-20 threaded stud. This
is the same thread that is on the T-SLOT fastener. The NLCA1
can be used for mounting single fixtures.
3. NLCA2 is a double point “Y” cable system that can be used for
different configurations.
FIGURE 8
FIGURA 8
POWERING THE FIXTURE(S) (See Figure 9):
1. Attach power cord to POWER IN panel connector.
2. An INTERCONNECT cord can be used to power multiple
fixtures or “DAISY CHAIN” fixtures together. Connect NO
MORE than
16 fixtures
on one power drop.
INTERCONNECT
CORD
POWER CORD
