Hubbell GAI-TRONICS RED ALERT 393-710 страница 9 Скачать руководство пользователя | Manualshive

Страница: 9 / 27

background image

Pub. 42004-541A

Hands-free VoIP Telephone Manual

Page 9 of 24

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-541A.docx

02/20

Conduit Installation Details (Surface-Mount Models)

GAI-Tronics recommends installing Ethernet and power lines in conduit to protect against accidental
damage and vandalism. To prevent moisture from entering the enclosure, the following is recommended:

•

Conduit should enter the enclosure from the bottom.

•

Sealed fittings should be installed at all cable entry points.

•

Silicone sealant or equivalent should be applied around and inside all conduit entries.

Please refer to the examples below for the recommended conduit installation details.

Figure 1. Bottom entry conduit recommended for

non-metallic enclosures

Figure 2. Top entry conduit installation for non-

metallic enclosures (NOT recommended)

Figure 3. Bottom entry conduit installation details

for metallic enclosures

Figure 4. Top entry conduit installation details for

metallic enclosures (NOT recommended)

«
...
7
8
9
10
11
...
»

Содержание GAI-TRONICS RED ALERT 393-710




























Отзывы:

Нет отзывов

Похожие инструкции для GAI-TRONICS RED ALERT 393-710

Бренд: Dinstar Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды