Hubbell GAI-TRONICS RED ALERT 393-710 Скачать руководство пользователя

Страница: 7 / 27

Pub. 42004-541A

Hands-free VoIP Telephone Manual

Page 7 of 24

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-541A.docx

02/20

•

warm reset (internal command)

•

keypad error (if applicable)

•

key hook (off hook status, if applicable)

•

audio path test (speaker/microphone test)

Status Indication

Power

The

LED, located on the VoIP PCBA (see Figure 21 on Page 18), illuminates when power is applied

to the telephone.

Heartbeat

The

LED, located on the VoIP PCBA (see Figure 21 on Page 18), flashes when communication over

the LAN is established.

Link

The

LED, located on the VoIP PCBA (see Figure 21 on Page 18), indicates an active network

connection when illuminated.

Speed

The

LED, located on the VoIP PCBA, (see Figure 21 on Page 18) indicates a 100 Mbps network

connection when illuminated or a10 Mbps connection when off.

VoIP Circuit PCBA Pushbuttons

Reset

Press the

RESET

button (see Figure 21 on Page 18) momentarily to warm reboot the telephone. The

telephone maintains the current configuration.

Factory

Use the

FACTORY

button (see Figure 21 on Page 18) to erase the current configuration and restore the

factory default settings as follows:

Press and release the

RESET

button.

Press and hold the FACTORY button for 10 seconds while the telephone is rebooting.

The telephone will reboot again with the factory default settings configured.

Содержание GAI-TRONICS RED ALERT 393-710




























Результаты поиска

Содержание GAI-TRONICS RED ALERT 393-710

Отзывы:

Похожие инструкции для GAI-TRONICS RED ALERT 393-710

Бренды по названию

Популярные бренды

Hubbell GAI-TRONICS RED ALERT 393-710, Руководство пользователя

Результаты поиска

Содержание GAI-TRONICS RED ALERT 393-710

Отзывы:

Похожие инструкции для GAI-TRONICS RED ALERT 393-710

Бренды по названию

Популярные бренды