Huawei V100R006C00 Скачать руководство пользователя страница 105

Страница: 105 / 142

If the number of the ACL that matches packets received by the CPU and the observing port are
displayed, the configuration is successful.

7.16 Cancelling CPU Mirroring

This section describes how to cancel CPU mirroring.

7.16.1 Establishing the Configuration Task

Applicable Environment

If packets received by the CPU of the S5700 do not need to be monitored, you can cancel CPU
monitoring.

Pre-configuration Tasks

None.

Data Preparation

To cancel CPU mirroring, you need the following data.

No.

Data

Number of the observing port

7.16.2 Cancelling CPU Mirroring

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

undo port-mirroring cpu

CPU mirroring is cancelled.

Step 3

(Optional) Run:

undo observe-port

index

The index of the observing port is deleted.

----End

7.16.3 Checking the Configuration

Run the following commands to check the previous configuration.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Содержание V100R006C00















































































































































Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды

Huawei V100R006C00, Руководство по настройке

Результаты поиска

Содержание V100R006C00

Отзывы:

Бренды по названию

Популярные бренды