manualshive.com logo in svg

Huawei V100R006C00, Руководство по настройке

Поделиться
Скачать
Huawei V100R006C00 Скачать руководство пользователя страница 101

Action

Command

Check the flow mirroring
configuration in the traffic policy
on an interface.

display traffic policy interface

 [ 

interface-type

interface-number

 ] [ 

inbound

 ]

 

If the following result is obtained, the configuration is successful:

The traffic policy applied on an interface is cancelled.

7.14 Changing or Deleting an Observing Port

This section describes how to change or delete an observing port.

7.14.1 Establishing the Configuration Task

Applicable Environment

When you do not need to monitor the flow passing through the S5700, you can delete the current
observing port; when you need to specify another interface on the S5700 as an observing port,
you can change the current observing port.

Pre-configuration Tasks

Before changing or deleting an observing port, complete the following tasks:

l

7.4 Canceling Port Mirroring

l

7.7 Canceling VLAN Mirroring

l

7.10 Canceling Mirroring Based on MAC Addresses

l

7.13 Canceling Flow Mirroring

Data Preparation

To change or delete an observing port, you need the following data.

No.

Data

1

Type and number of the new observing port

 

7.14.2 (Optional) Deleting an Observing Port

Prerequisite

Before deleting an observing port, make sure that the observing port is not used in any mirroring
configuration.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

92

Содержание V100R006C00















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды