Huawei UPS5000-S-1200 kVA Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 215

background image

UPS5000-S-1200 kVA
User Manual

5 Operations

Issue 04 (2019-06-25)

Copyright © Huawei Technologies Co., Ltd.

172

Figure 5-12

Starting a forced equalized charging test

The forced equalized charging test automatically stops in any of the following cases:



The forced equalized charging test duration reaches the forced equalized charging protection time
(12–24 h, 18 h by default).



The UPS generates a battery overtemperature, overvoltage, or overcurrent alarm.



An alarm is generated.

----End

5.6.2 Shallow Discharge Test

Before performing a shallow discharge test, ensure that:



The UPS works in normal mode with a load ratio fluctuation less than 10%.



The UPS generates no battery overtemperature, overvoltage, or overcurrent alarm. No
generator is connected to the UPS.



The mains, batteries, charger, and discharger are normal. No overload alarm is generated.

If the battery strings of two power units are shared, you only need to perform the shallow
discharge test for one power unit to complete all battery tests. If the battery strings are not
shared, you need to perform the shallow discharge charging test on the LCD of both power
units to complete all battery tests.

Automatic Shallow Discharge Test

Step 1

On the main screen of the power unit LCD, choose

Power Unit N Info.

>

Settings

>

Battery

Param.

, and set

Sched. shallow dis. test

to

Enable

.

Step 2

Set

Sched. shallow dis. test time

and

Sched. shallow dis. test interval

as required. After

setting is complete, the system will perform automatic shallow discharge tests based on the
settings.

----End

«
...
178
179
180
181
182
...
»

Содержание UPS5000-S-1200 kVA
























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UPS5000-S-1200 kVA

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: Pari Страницы: 282

Бренд: Baileigh Industrial Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды