Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 77

Страница: 77 / 175

Figure 6-9 Preparing a cable terminal outside the cabinet

NO TE

Choose an appropriate cabling route based on the actual situation. The figure is for

reference only.

Step 4 Connect the cable with a crimped terminal to the corresponding copper bar.
Step 5 Clear sundries inside the cabinet.

----End

6.3 Single UPS Installation (400–600 kVA)

CA UTION

When you install the UPS and connect cables, do not step on the front door baffle

plate and the door support at the bottom of the cabinet to prevent paint flake-off

and deformation. Otherwise, the front door will not be properly closed.

6.3.1 Installing the UPS

6.3.1.1 Installing the Cabinet

Installation on the Floor

NO TICE

Ensure that the installation floor is level.

Step 1 Install the cabinet.

1. Determine the mounting holes for the cabinet based on the marking-off

template. A indicates the mounting holes for channel steel. B indicates the

mounting holes for the floor. The unit is mm.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

6 Installation

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды