Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 53

Страница: 53 / 175

Optional

Component

Model

Function

Surge protection

box subrack

Installed when a surge protection box is

used.

Ambient

temperature

and humidity

sensor

Monitors ambient temperature and

humidity.

Battery

temperature

sensor

Monitors the battery temperature.

BSC cable

5 m/10 m/15

m/60 m

Transmits bus synchronization signals in a

dual-bus system.

Parallel cable

5 m/10 m/15 m

Connects UPSs in parallel.

Bottom cabling

cabinet

Applies to the bottom cabling scenario.

Rear copper bar

protection

component

Protects copper bars at the rear of the

cabinet.

NO TE

The ECM extended subrack, surge protection box subrack, and intelligent detection card do

not support onsite installation. If you require the optional components, inform Huawei

when you purchase the UPS so that Huawei can install them before delivery.

5.2 Dry Contact Extended Card

The dry contact extended card provides five groups of electric relay output ports

for dry contact signals and five groups of signal input ports to implement various

alarm and control functions as required.
A maximum of one dry contact extended card supported in the power monitoring

subrack. The card is hot swappable.

Figure 5-1 Appearance

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

5 Optional Components

Issue 02 (2021-04-22)

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды